| 33 0941 01 Rollix Slewing Ring Bearings | Number of Lubrication Holes:12; Chamfer r1smin2:12.5 mm; Outer-Ring Set:540RXS2345; Type:RX-4; Lubrication Hole Diameter h:9.5 mm; Static Load Rating Co:9520 kN; Inner-Ring Set:500ARXS2345A; Dynamic Load Rating C11:22200 kN; Bore d:500.000 mm; DUR/DOR F/E:540.000 mm; Weight:1007.300 lb; Width C:450.000 mm; Angle of Chamfer r1smin:20º; Backing Shaft Diameter ds:531.0 mm; Lubrication Groove g:19.3 mm; |
| 33 0541 01 Rollix Slewing Ring Bearings | Full Timken Part Number:QMMH18J090SB; Grease Lubrication - B/C/O Seal:1000 rpm; Oil Lubrication - B/C/O Seal:1000 rpm; Shaft Size Type:Metric; Thread Size J:1 1/4-7UNC; e - Geometry Factor:0.23; Pre Install Clearance Min:0.0024 in; Dimension A:6.31 in; Dimension R:0.12 in; Dimension L:3.910 in; Dimension M:2.59 in; C - Dynamic Load (Basic):79700 lb; Housing Style:Hanger; Locking Style:Eccentric; Y2 - Geometry Factor:4.31; |
| 1 3031 Rollix Slewing Ring Bearings | C1 - Cup Flange Width:0.1090 in; D:1.8504 in; e - ISO Factor8:0.36; Cup Part Number:05185-B; Cg - Geometry Factor11:0.0448; Cone Part Number:05075; db - Cone Backface Backing Diameter:0.98 in; d:0.7500 in; T - Bearing Width to Flange:0.2377 in; D1 - Flange Outer Diameter:2.0024 in; R - Cone Backface To Clear Radius1:0.050 in; Design Units:Imperial; Ca90 - Dynamic Thrust Rating (90 million revolutions)6:952 lbf; |
| 25 0741 01 Rollix Slewing Ring Bearings | Dimension C:6.00 in; Shaft Size :3-15/16 in; UPC Code:0883450040808; Engineering Group:Mounted Bearing; Eng Internal Radial Clearance - Max:0.0047; Dimension L Exp:5.29 in; C0 - Static Load:113000 lb; Grease Lubrication - M/N Seal:1200 rpm; e - Geometry Factor:0.24; Y2 - Geometry Factor:4.23; Dimension F:9.500 in; Housing Style:Four-Bolt Square Fla; Eng Internal Radial Clearance - Min:0.0030; |
| 8 0270 04 Rollix Slewing Ring Bearings | Dimension L2:12.70 mm; Static Load Rating:1460 lbf; Dimension P:1.311 in; Total Height H:92.1 mm; Total Length L:100.8 mm; Seal Type:Molded Shroud; Slot Width A1:13.5 mm; Housing Width A:13.5 in; Center of Bearing from End S:7.49 mm; Weight:3.02 lb; Height H2:57.2 mm; Dynamic Load Rating:3190 lbf; Opening Width N1:15.9 mm; Bearing Number:GRAE20RRB; Shaft Size d:0.787 in; Housing Style:Take-Up; Opening Height N2:31.8 mm; |
| 3 026 Rollix Slewing Ring Bearings | Y2 - ISO Factor6:2.57; D:290.000 mm; B - Outer Ring Width:80 mm; Cage Material:Brass; Reference Thermal Speed Rating (Oil)7:2200; Y0 - ISO Factor4:2.62; d:160 mm; C1(2) - Dynamic Radial Rating (Two-Rows):1120000 N; Bearing Weight:23 Kg; Reference Thermal Speed Rating (Grease):1900; Design Unit:METRIC; Y1 - ISO Factor5:3.91; B - Inner Ring Width:80 mm; Bore Taper:1/12; da - Inner Ring Backing Diameter:192.000 mm; |
| 6 0307 Rollix Slewing Ring Bearings | C0 - Static Load:48600 lb; Float:0.08 in; Dimension C:0.88 in; Grease Lubrication - T Seal:2800 rpm; Dimension L:7.63 in; Locking Style:Single Concentric; Shaft Size :65 mm; Oil Lubrication - M/N Seal:1800 rpm; Dimension D:5.88 in; Eng Internal Radial Clearance - Min:0.0016; Housing Style:Take-Up; Dimension S:1.060 in; Shaft Size Type:Metric; C - Dynamic Load (Basic):46400 lb; Dimension G:1.31 in; |
| 1 2560 01 Rollix Slewing Ring Bearings | Aa - Cage-Cone Backface Clearance:0.8 mm; e - ISO Factor8:0.45; d:28.575 mm; Cup Part Number:02820; C90 - Dynamic Radial Rating (90 million revolutions)4:3830 lbf; Cone Part Number:02872; B:22.225 mm; C1 - Dynamic Radial Rating (1 million revolutions)5:14800 lbf; da - Cone Frontface Backing Diameter:37.08 mm; r - Cup Backface To Clear Radius2:3.30 mm; Y - ISO Factor9:1.32; a - Effective Center Location3:-3.8 mm; |
| 2 256 Rollix Slewing Ring Bearings | H:128 mm; A:95.00 mm; Shaft Diameter db:55 mm; H2:28.00 mm; Cage Type:EJ; J2:234 mm; A1:70 mm; Housing Mass:4.5 Kg; Max Oil Speed:6500; Max Grease Speed:5300; Seal:TA309; Bearing:21309; Shaft Diameter da:45 mm; C1 Dynamic Load Rating:138; C0 Static Load Rating:125; Locating Rings (width x OD):SR100X9.5; G:M12; Housing:FSNT 511-609; J1:35 mm; J:210.00 mm; |
| 121.45.5300.990.41.1502 Standard 5 Slewing Ring Bearings | Cage Type:EJ; Shaft Diameter da:40 mm; Jmin:165 mm; A2:102 mm; End Cover1:EC510-608; A:90.00 mm; Max Grease Speed:5800; H1:60.0 mm; Seal:LO308; G:M12; Max Oil Speed:7100; N:15 mm; Bolt Qty:2; H2:25.0 mm; N1:20.00 mm; A1:60 mm; Shaft Diameter db:50 mm; L:205.00 mm; Seal Type:Labyrinth; C0 Static Load Rating:102; |