| HT10-54N1Z Kaydon Slewing Ring Bearings | A:45 mm; J max.:133 mm; Hexagonal key size for grub screw N:3 mm; Recommended diameter for attachment bolts, inch G:0.5 in; H2:19 mm; H:93 mm; N1:14 mm; H1:47.6 mm; d:34.925 mm; J6:146 mm; N4:4 mm; Housing material:Cast iron; Basic dynamic load rating C:25.5 kN; B1:39.5 mm; Housing:SY 507 M/VZ033; Thread grub screw G2:M6; Mass bearing unit:1.5 kg; J:126 mm; Recommended tightening torque for grub screw:7.4 N·m; |
| RK6-22N1Z Kaydon Slewing Ring Bearings | h:96.5 mm; Specific dynamic load factor K:25 N/mm²; Coefficient of friction µ max.:0.15; Mass bushing:4.65 kg; D:115 mm; Permissible sliding velocity v max.:0.5 m/s; B:160 mm; a:8 mm; Specific static load factor K0:45 N/mm²; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; Coefficient of friction µ min.:0.08; d:95 mm; α:124 °; Tolerance shaft:e7; |
| 16348001 Kaydon Slewing Ring Bearings | d:200 mm; Coefficient of friction µ min.:0.03; Mass bushing:2.22 kg; Specific static load factor K0:200 N/mm²; Permissible sliding velocity v max.:0.5 m/s; Tolerance shaft:h8; Specific dynamic load factor K:140 N/mm²; Effective load carrying cross section A:35600 mm²; D:220 mm; B:180 mm; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; Coefficient of friction µ max.:0.08; |
| MTE-324X Kaydon Slewing Ring Bearings | P180°:57.4 kN; Ca:55.804 mm; R2:30.163 mm; Taconite seal:TER 113; H1:114.3 mm; Housing:SSAFS 024 KA; L:387.35 mm; Pa:16.7 kN; Cap bolt recommended tightening torque:298.3 N·m; Da:180 mm; Initial grease fill:181.44 g; P60°:141 kN; Eye bolt:2 x 3/8-16 UNC; P120°:52.5 kN; Mass pillow block:39.5 kg; ba:46.831 mm; Cap bolt, SAE grade:8; Stabilizing ring:2 x 38151-24; Cap bolt:5/8-11 UNC; |
| XU160405 INA Slewing Ring Bearings | Weight W:2.65 lb; Dimension N:1.0625 in; Dimension B:4.7500 in; Dimension G:0.5625 in; Dimension S1:1.2813 in; Dimension L:5.8125 in; Dimension D2:3.5625 in; Dimension H:1.5000 in; Shaft Diameter D:1 15/16 in; Basic Dynamic Radial Load Rating:7890 lbf; Insert Bearing IB:ZMaRC; Dimension J:1.9375 in; Dimension C:4.0000 in; Basic Static Radial Load Rating Co:5220 lbf; Width A:1.6250 in; Pin Dia A1:0.6875 in; |
| MTO-265X Kaydon Slewing Ring Bearings | Labyrinth seal:2 x TS 64; db:300 mm; H2:100 mm; Bearing (basic designation):23056; Mass housing:221 kg; Pa:1200 kN; Taconite seal:2 x TK 64; P90°:2300 kN; P0°:3800 kN; P150°:1500 kN; H1:260 mm; Q120°:2860 kN; J1:160 mm; H:516 mm; bc:151.5 mm; Q150°:1650 kN; Appropriate attachment bolt, size G:36 mm; Da:420 mm; A:320 mm; Appropriate attachment bolt, rec. tightening torque:2280 N·m; |
| 16366001 Kaydon Slewing Ring Bearings | Accessories:Two Seals & Snap-Rin; Oil Speed Rating Open/Shielded n2:10000 rpm; Grease Speed Rating Open/Shielded n1:8500 rpm; B:23.00 mm; Basic Static Radial Load Rating Co:23600 N; d:30.000 mm; D:90.0000 mm; Fillet Radius ra:1.50 mm; Sealed Speed Rating n3:5600 rpm; Basic Dynamic Radial Load Rating C:43600 N; |
| 16320001 Kaydon Slewing Ring Bearings | h1:230 mm; C1 max.:48 mm; G:M 64x4; l3 min.:85 mm; Mass rod end:15 kg; Material constant KM:330; r1 min.:1 mm; α:5 °; d:80 mm; w:90 mm; Basic dynamic load rating C:400 kN; l4 max.:324 mm; Basic static load rating C0:655 kN; l7 min.:90 mm; d4 ≈:105 mm; l5 ≈:45 mm; Specific dynamic load factor K:100 N/mm²; d2 max.:182 mm; dk:105 mm; B:55 mm; |
| MTE-590T Kaydon Slewing Ring Bearings | Fillet Radius ra:1.50 mm; Oil Speed Rating Open/Shielded n2:8500 rpm; Basic Dynamic Radial Load Rating C:55300 N; Accessories:Two Shields & Snap-R; D:100.0000 mm; Basic Static Radial Load Rating Co:31000 N; Grease Speed Rating Open/Shielded n1:7000 rpm; d:35.000 mm; B:25.00 mm; Sealed Speed Rating n3:4900 rpm; |
| VU25038 INA Slewing Ring Bearings | r1,2 min.:6 mm; d1:420 mm; d:220 mm; Mass shaft washer:32.2 kg; B:41 mm; |